Three Phase Pump Control Box: Is Matching Motor Power Enough?
A three phase pump control box must match the motor’s voltage, current and operating requirements, not just its kW rating. Liyuan’s control-box catalog lists C3-SP1 for 0.75–4 kW motors and C3-SP2 for 5.5–7.5 kW motors, with a nominal three-phase 380 V input and 50/60 Hz supply frequency.
Those ratings provide a shortlist. Before ordering, confirm the current-setting range, required protection functions and what the pump will do after a fault or power interruption.
Which Three Phase Pump Control Box Matches Your Motor?
| Catalog Item | C3-SP1 | C3-SP2 |
|---|---|---|
| Listed motor-power range | 0.75–4 kW | 5.5–7.5 kW |
| Nominal input supply | Three-phase AC 380 V | Three-phase AC 380 V |
| Supply frequency | 50/60 Hz | 50/60 Hz |
The model ranges come from the ordering table on page 4 of Liyuan’s supplied 2026 control-box catalog. The page presents protection and control features under the C3-SP1 heading; confirm the feature configuration supplied with C3-SP2 when requesting a quote.
For example, a 4 kW motor falls within the listed C3-SP1 power range. That does not confirm compatibility if its voltage, nameplate current or starting requirements differ from the proposed controller.
Send a clear motor-nameplate photo. Ask the supplier to confirm the controller’s allowable current range and protection settings against that motor.
A larger box is not automatically a better replacement. Its sensing and adjustment range must still suit the smaller motor.
Can A 380 V Pump Controller Be Used On 400 V Or 415 V?
Do not assume compatibility from the nominal voltage alone.
The supplied catalog identifies AC 380 V but does not state the full acceptable input-voltage range or the under/overvoltage trip thresholds. A quotation for a 400 V or 415 V installation therefore needs written confirmation for that supply and motor combination.
Likewise, the 50/60 Hz label does not mean the controller converts frequency. A 50 Hz motor and pump cannot be treated as a verified 60 Hz package simply because the control box supports both supply frequencies.
For sites with recurring voltage faults, the submersible pump voltage protection article explains the checks to discuss with your installer. Protection settings should follow the selected motor and controller documentation, not a generic percentage copied from another product.
Does Phase-Loss Protection Cover Every Three-Phase Fault?
No. Missing a phase, reversing phase sequence and operating with unequal phase currents are different conditions.
The C3-SP1 catalog page specifically lists:
- Overload protection.
- Under/overvoltage protection.
- Motor-stall protection.
- Sensor-free dry-run protection.
- Open-phase protection.
Open-phase protection is the catalog’s wording for phase-loss protection. The page does not explicitly specify phase-reversal protection or voltage/current imbalance thresholds.
For comparison, Franklin Electric’s SubMonitor Connect specifications list current phase unbalance and reverse phase as separate functions. This illustrates why buyers should request named protections rather than accept “complete motor protection” as a specification. It does not establish equivalent functions in a Liyuan controller. Franklin Water
If the installation requires phase-sequence monitoring or imbalance protection, include that requirement in the inquiry and obtain confirmation of the supplied arrangement.
Will The Pump Restart Automatically After A Fault?
This matters when a borehole fills a remote irrigation tank or operates without an attendant.
The catalog lists manual/automatic operation, push-button calibration, the last five fault records and accumulated running time. It also states that protection functions operate in both manual and automatic modes.
However, the brochure does not clearly define the restart delay, number of retry attempts or reset method for each fault.
Ask the supplier to complete this operating sequence before delivery:
| Event | Required Confirmation |
|---|---|
| Supply power returns | Does the pump remain stopped or resume when demand is present? |
| Dry-run protection trips | Is restart manual or timed, and what recovery delay applies? |
| A phase is lost | What conditions must be restored before restarting? |
| Overload or stall occurs | Is inspection and manual reset required? |
| Tank reaches its stop level | Which input stops the pump, and what starts it again? |
Do not assume all faults use the same restart logic. An unattended system needs an agreed operating sequence, not merely an Auto button.
Can It Control A Tank And Maintain Constant Pressure?
The catalog lists control inputs for an electrode probe, float switch, electric-contact pressure gauge and pressure switch. Confirm the supported wiring and operating mode for the selected input; the list does not prove every input can be combined simultaneously.
For tank filling, specify the start and stop levels. For pressure-switch operation, specify the required cut-in and cut-out pressures.
A pressure-switch input does not by itself establish variable-speed constant-pressure control. The C3-SP1 page does not identify the box as a VFD. If continuously adjusted motor speed is required, request a suitable drive-based system instead.
The submersible pump pressure switch article covers the difference between pressure-switch cycling and variable-speed pressure control.
What Should You Send Before Ordering?
For a three phase pump control box quotation, provide:
- Motor nameplate, including kW, voltage, frequency and rated current.
- Site supply voltage and whether power comes from the utility or a generator.
- Required start/stop method: manual, tank level or pressure switch.
- Required phase, dry-run and overload protection functions.
- Restart requirements after power loss and each fault.
- Installation environment and existing starter or drive details.
The C3-SP1 page lists IP22. Do not specify exposed outdoor installation from that rating alone; request an enclosure arrangement suitable for the actual rain, dust, condensation and temperature conditions.
Have a qualified electrical installer verify the wiring, isolation, earthing and required upstream protection. The brochure’s motor-protection list is not a complete electrical-installation specification.
Email Liyuan Pump with these details and request a confirmed C3-SP1 or C3-SP2 configuration, wiring diagram and parameter instructions. The useful outcome is a controller matched to the motor and operating sequence—not simply a box carrying the same horsepower label.
Email:Liyuan@liyuan-pump.com
WhatsApp:+86 181-2828-2767

