A 10 inch submersible pump cannot be selected or replaced by motor power alone. Liyuan’s catalog lists both the 10SG125/6 and 10SG160/5 with 63 kW motors, but their performance differs: at 100 m³/h, their listed heads are 142 m and 129 m; at 160 m³/h, they are 87 m and 100 m.
That difference matters when a buyer needs to replace a borehole pump without changing the motor size—or when two suppliers quote the same power but different hydraulic models.
10 Inch Submersible Pump Comparison: Same Power, Different Performance
| Catalog Item | 10SG125/6 | 10SG160/5 |
|---|---|---|
| Listed motor power | 63 kW / 85 HP | 63 kW / 85 HP |
| Head at 100 m³/h | 142 m | 129 m |
| Head at 160 m³/h | 87 m | 100 m |
| Pump-body length | 1,322 mm | 1,226 mm |
| Pump-body weight | 63 kg | 58 kg |
Source: Liyuan Pump’s 2026 catalog, PDF page 19, printed page 16. Length and weight refer to the pump body, not the complete installed pump-and-motor assembly.
The selected model values above also appear in the archived Liyuan pump catalog. Catalog editions differ in some details; confirm the current specification before ordering.
The catalog page does not identify the frequency for these values. Request the current complete pump curve for your supply frequency and the exact quoted configuration. The values above are catalog points, not measured performance at your site.
Which 63 kW Pump Fits The Required Duty?
Suppose a water project requires 100 m³/h at 135 m total dynamic head. At 100 m³/h, the catalog lists 142 m for the 10SG125/6 and 129 m for the 10SG160/5.
On that preliminary comparison, the 10SG125/6 is a candidate; the 10SG160/5 is below the stated head requirement. The candidate still needs curve, operating-range and system checks.
For a different project requiring 160 m³/h at 95 m total dynamic head, the comparison changes. The catalog lists 87 m for the 10SG125/6 and 100 m for the 10SG160/5. Here, the 10SG160/5 is the candidate; the 10SG125/6 is below the requirement.
These are two separate illustrations, not a single installation. Each head must be calculated at its corresponding required flow, including pumping water level, outlet pressure, elevation and friction losses.
Can You Replace A 10 Inch Submersible Pump With The Same kW?
Possibly, but the same kW rating does not prove hydraulic or installation compatibility. In the examples above, switching between the two 63 kW models changes which requirement can be met.
Before replacing a deep well pump, ask the supplier to confirm:
- The proposed model’s flow and head at the actual duty point.
- Its permitted operating range and motor loading.
- The assembly diameter, length and discharge connection.
- Motor voltage, phase, frequency and compatibility with the existing starter or drive.
- Well yield, pumping water level and motor cooling conditions.
If the old pump has lost performance, first identify whether the cause is pump wear, a pipe leak, an electrical fault or a falling water level. The submersible pump replacement checklist explains what to verify before reusing an old model as the specification.
Does A Higher Catalog Head Mean More Water On Site?
Not necessarily. A pump’s actual flow depends on the complete system, not on a single catalog value.
KSB explains the operating point as the intersection of the pump curve and the system curve. A new pump may operate at a different flow from the old one if its curve differs.www.ksb.com
For the proposed replacement, request the complete performance curve with the required point marked. Check the likely operating range as water level, demand and system resistance change. Do not treat the highest listed flow or shut-off head as the normal duty point.
Will A 10 Inch Borehole Pump Fit The Existing Well?
The 10-inch designation alone does not prove that an assembly will fit a particular well. Obtain the actual smallest internal casing diameter and compare it with the supplier’s maximum assembled dimensions, including cable protection and any fittings.
For example, the catalog lists a 1,322 mm pump-body length for the 10SG125/6. This is not the overall length with motor, coupling and installation fittings. Request a complete assembly drawing, including maximum diameter and connection details.
The 2026 catalog shows the outlet notation as 6″ (5″), but does not explain the parenthetical value on that page. Confirm the actual outlet size and connection type for the quoted pump before ordering pipework or adapters.
Can The Existing Cable And Starter Be Reused?
Do not assume that a 63 kW replacement can use the existing electrical equipment solely because the previous motor was also 63 kW.
Ask the motor and control suppliers to check the nameplate voltage, frequency, phase and full-load current against the cable length and size, starting method and protection settings. If a variable frequency drive is installed, check the motor-drive combination and permitted operating range as well.
Reuse may be possible after verification; matching motor power is only the starting point.
What Does The Stainless Steel Description Cover?
Liyuan’s catalog describes the series as SG-SS impeller. It does not establish that the entire pump is stainless steel, identify a stainless grade for every wetted component, or confirm a drinking-water certification.
If the well contains sand or chemically aggressive water, provide the available water analysis and ask for the quoted materials and allowable conditions in writing.
What Should A Buyer Send For A 10 Inch Submersible Pump Quote?
To compare quotations on the same basis, send Liyuan Pump:
- Required flow and total dynamic head at that flow.
- Measured pumping water level and sustainable well yield.
- Smallest casing internal diameter and any known restrictions.
- Existing pump and motor nameplate photos, if this is a replacement.
- Supply voltage, frequency, phase, cable length and control method.
- Water temperature, sand content and water analysis, if available.
Ask for the exact model, a current curve marked at the duty point, the motor data sheet, complete assembly dimensions and a confirmed outlet connection.
For a 10 inch submersible pump, the correct replacement is the model that meets the required flow and head and fits the existing system—not simply the model with the same motor power.
Email:Liyuan@liyuan-pump.com
WhatsApp:+86 181-2828-2767

