5 Inch Submersible Motor: Specs And 6-Inch Comparison

Table of Contents

5 Inch Submersible Motor

5 Inch Submersible Motor: When Should You Choose It Over A 6-Inch Motor?

A 5 inch submersible motor is worth evaluating when assembly diameter limits your borehole pump selection, but it is not automatically shorter, lighter or electrically interchangeable with a 6-inch motor. Liyuan’s supplied catalog lists a three-phase, water-cooled 5-inch range from 4 to 15 kW.

Choose between the two sizes using the complete assembly drawing and confirmed electrical data. The same motor power does not mean the same dimensions, operating current or pump-end compatibility.

What Specifications Does Liyuan List For Its 5 Inch Submersible Motor?

The following values are transcribed from the supplied 2026 catalog, printed page 9.

Motor PowerListed CurrentListed LengthListed Weight
4 kW11.0 A750 mm39 kg
5.5 kW14.3 A800 mm42 kg
7.5 kW19.0 A823 mm45 kg
9.2 kW23.0 A903 mm52 kg
11 kW27.5 A985 mm60 kg
13 kW32.0 A1,073 mm68 kg
15 kW36.0 A1,163 mm75 kg

The table heading states three-phase, water-cooled, 380–415 V and 50/60 Hz. It does not provide separate current values for each voltage and frequency combination.

Use these figures for preliminary comparison—not as final overload settings or cable-sizing instructions. Request the exact nameplate and electrical data for the version being quoted.

Liyuan’s public 5- and 6-inch motor datasheet also contains these 5-inch values. Confirm the document revision attached to your order. liyuan-pump.com

Is A 5-Inch Motor Always Smaller In Every Dimension?

No. The size designation does not describe the whole installation envelope.

Compare two 7.5 kW water-cooled entries in the supplied catalog:

Item5-Inch Entry6-Inch Entry
Listed current19.0 A17.5 A
Listed motor length823 mm804 mm
Listed motor weight45 kg49 kg

At this power, the 5-inch entry is 19 mm longer but 4 kg lighter. That can matter when handling the assembly or fitting it through limited service access.

The pattern changes at 15 kW. The 5-inch entry is listed at 1,163 mm and 75 kg, while the 6-inch entry is 1,046 mm and 67 kg. Here, the 5-inch option is both longer and heavier.

These comparisons describe the listed motor entries, not complete pump-set dimensions. Ask for the assembled pump-and-motor length, maximum outside diameter and lifting weight before planning installation.

Will A 5 Inch Submersible Motor Fit A 5-Inch Well?

The name alone cannot establish fit.

The catalog performance table does not give the maximum outside diameter of the selected motor with its lead connection and cable arrangement. It also does not establish the maximum diameter of the attached pump end.

A usable fit check needs:

  • The smallest actual casing or liner internal diameter.
  • The maximum pump-and-motor assembly diameter.
  • Cable-guard, coupling-area and pipe-connection clearances.
  • Adequate allowance for installation and later retrieval.

Motor-body size and mounting-interface size should also be treated separately. For example, Franklin Electric describes an 8-inch motor with a 6-inch pump mounting surface. That illustrates why a size label is not a complete interface specification; it does not confirm any Liyuan cross-brand interchangeability. Franklin Water

Does The Lower Listed Current Make The 6-Inch Motor More Efficient?

Not by itself.

The catalog lists different currents for the two 7.5 kW entries, but current alone is not an efficiency measurement. A valid efficiency comparison needs confirmed voltage, frequency, load, power factor, electrical input and shaft output under comparable conditions.

The supplied table does not provide efficiency curves or enough test conditions to support a claim that one size saves a stated percentage of electricity.

For a continuously operated irrigation or groundwater supply system, request efficiency data at the expected load. Compare the complete motor-and-pump combination, rather than treating the lower current entry as proof of lower operating cost.

Can You Keep The Existing Pump End, Cable And Controller?

Only after checking them against the proposed motor.

Pump end: Confirm the mounting dimensions, shaft connection, rotational speed, required shaft power and allowable thrust. Matching kW alone does not approve the mechanical combination. The submersible pump coupling article explains the shaft and engagement details needed for a fit check.

Cable: Use the confirmed motor current, supply voltage, full cable length and installation conditions. A cable suitable for one motor is not automatically suitable for another of equal power. The submersible pump cable selection article covers the information needed for that calculation.

Controller: Check its voltage rating, current range, starting method and protection settings. If a VFD is involved, obtain the motor’s permitted operating-frequency range and cooling requirements.

Have the electrical checks and commissioning performed by a qualified installer. Do not copy the previous motor’s settings without reviewing the replacement.

What Should You Request With A 5 Inch Submersible Motor Quote?

Send the required motor power, site voltage and frequency, pump-end model, casing internal diameter, cable length and control method. For a replacement, include photographs of the existing motor nameplate and mounting interface.

Ask for a quotation identifying:

  • The exact motor model and electrical version.
  • Confirmed current and connection details.
  • A dimensional drawing, including the shaft and mounting interface.
  • Permitted thrust load and approval for the proposed pump end.
  • Cooling-flow, water-temperature and installation-orientation limits.
  • Whether the supply is motor-only or a complete pump assembly.

The supplied performance table is useful for comparing available sizes, but it does not answer all these installation questions.

Email Liyuan Pump with your existing equipment details and dimensional constraints. Request a 5 inch submersible motor proposal and, where space permits, a comparable 6-inch option. Compare confirmed fit, loading and operating data before selecting either configuration.

Email:Liyuan@liyuan-pump.com

WhatsApp:+86 181-2828-2767

Phone: USA 86-134 2250 1007

General Questions
Quotes, Please use Sales Quote Form HERE Email: liyuan@liyuan-pump.com
Quick Connect
Scroll to Top

Get a Quote