4SG Submersible Pump: Stainless Steel Impeller Models

Table of Contents

4SG Submersible Pump

4SG Submersible Pump: Stainless Steel Impeller Models

A Liyuan 4SG submersible pump belongs to the 4-inch stainless steel impeller range listed in Liyuan’s catalogue. The range includes 4SG2, 4SG3, 4SG5, 4SG8 and 4SG14 hydraulic families. Choosing between them requires a flow-and-head comparison, not just a stainless steel specification or motor horsepower.

For example, the catalogue lists both 4SG8/12 and 4SG8/15 with a 3 HP, 2.2 kW motor. At 8 m³/h, their listed heads are 50 m and 63 m respectively. They are not interchangeable simply because the motor ratings match.

This page compares Liyuan’s catalogue configurations and explains what to confirm before ordering. A similar 4SG designation from another manufacturer does not establish equivalent materials, dimensions or performance.

What Does The Liyuan 4SG Range Include?

Liyuan identifies this section of its catalogue as a 4-inch submersible pump range with stainless steel impellers. The two performance-table pages contain 50 model entries across five hydraulic families.

The distinction matters when specifying a borehole pump. A stainless steel exterior alone does not tell the buyer what the impellers are made from. Here, the catalogue explicitly identifies stainless steel impellers, but the performance pages do not provide a component-by-component material grade list.

The model tables are useful for shortlisting. They are not a substitute for an approved curve, assembly drawing or materials schedule for the exact supplied configuration.

Also clarify whether the quotation covers the pump end alone or the complete pump-and-motor assembly. A motor power column does not, by itself, define everything included in the price.

Compare 4SG Submersible Pump Flow And Head

The following examples show how the hydraulic families differ. Each flow and head belongs to the same catalogue operating point; the table does not combine maximum flow with maximum head.

Hydraulic FamilyExample ModelListed Motor PowerFlow At The Selected PointHead At That Flow
4SG24SG2/181 HP / 0.75 kW2 m³/h79 m
4SG34SG3/222 HP / 1.5 kW3 m³/h91 m
4SG54SG5/172 HP / 1.5 kW5 m³/h73 m
4SG84SG8/153 HP / 2.2 kW8 m³/h63 m
4SG144SG14/104 HP / 3 kW14 m³/h39 m

Source: Liyuan’s supplied 2026 pump catalogue, PDF pages 9–10, printed pages 6–7. These are catalogue values for initial comparison. Confirm the applicable frequency, speed and current curve revision before making a final selection.

Start with the flow your installation actually needs. A small tank-filling duty and a larger irrigation zone may require different hydraulic families even when the well diameter is identical.

Next, compare the available head at that flow with your total dynamic head. Total head includes the pumping water level, discharge elevation, required outlet pressure and system losses, without counting the same elevation twice.

Do not assume the family number is a guaranteed delivery rate under every condition. The actual operating flow depends on the pump curve and the connected system. Our submersible pump performance curve guide explains how to read those relationships.

Why Two 3 HP Models Can Give Different Results

Consider a preliminary requirement of 8 m³/h at 60 m total dynamic head. This is an illustrative selection exercise, not a customer installation or a factory test report.

The catalogue gives these points for two 4SG8 configurations:

Flow4SG8/12 Head4SG8/15 Head
0 m³/h70 m87 m
5 m³/h57 m71 m
8 m³/h50 m63 m
10 m³/h41 m51 m

Both models are listed at 3 HP / 2.2 kW. However, 4SG8/12 supplies only 50 m of head at the requested 8 m³/h. Its 70 m value occurs at zero flow and cannot be used to claim that it meets an 8 m³/h, 60 m requirement.

The 4SG8/15 has a listed 63 m at 8 m³/h, so it is a candidate for further review. That does not mean it will automatically operate at exactly 8 m³/h in the proposed installation.

As KSB explains the operating point, a centrifugal pump operates where its pump curve intersects the system curve. Changes in system resistance or water levels can move that point.

Before approving 4SG8/15 for this example, review the complete curve at the actual frequency, the expected water-level range, motor loading, permitted flow range and pressure limits. The apparent 3 m difference between the catalogue point and the example requirement is not automatically an adequate design allowance.

For a replacement, this comparison also shows why “another 3 HP pump” is an incomplete instruction. Supply the old pump and motor nameplates together with the current required duty. The submersible pump replacement checklist helps identify which existing components need compatibility checks.

Which Catalogue And Frequency Should You Use?

Use a curve that matches the quoted model, hydraulic configuration and operating frequency. Do not combine values from different catalogue editions to create a more attractive specification.

For the supplied catalogue used here, 4SG2/18 is listed at 2 m³/h and 79 m head. If another document or quotation shows a different value for that model, ask Liyuan to identify the applicable revision and test conditions before comparing offers.

The 4SG table pages do not explicitly label their operating frequency. Therefore, the figures on this page should not be treated as a verified 60 Hz performance chart, nor should a buyer assume that the same values apply at both 50 Hz and 60 Hz.

Request the actual pump curve and matched motor nameplate details. A controller marked 50/60 Hz does not resolve the hydraulic performance question.

For purchasing records, keep the approved curve revision with the quotation. That gives both parties a specific performance document to refer to instead of relying on a model name and an old screenshot.

What Does Stainless Steel Impeller Construction Confirm?

For this Liyuan range, the catalogue heading confirms the stated impeller material category: stainless steel.

It does not establish that every component is AISI 304 or AISI 316. It also does not establish a universal service life, a corrosion-free operating envelope or a sand-proof design.

Before accepting a material specification, request the grade and construction for the impellers, diffusers, pump casing, shaft, intake and discharge components. Confirm bearings, bushings and seals separately rather than assuming they use the same material as the impellers.

If the purchasing specification requires a particular stainless steel grade, have that requirement included in the confirmed quotation. Do not infer the grade from a polished surface or a generic stainless steel product title.

Our well pump impeller material comparison addresses the broader stainless steel versus engineered-plastic question. For a 4SG purchase, the next step is narrower: verify the material schedule for the exact model being offered.

There is also no basis in these two performance tables for claiming that a 4SG configuration uses less electricity than a different Liyuan series. An energy comparison needs efficiency and input-power information at the same required duty, not just matching motor ratings.

Is A 4SG Pump Suitable For Your Water?

Stainless steel impellers are not sufficient evidence to approve a pump for brackish water, chemically aggressive water or a sand-producing well.

For corrosion review, provide a water analysis that includes relevant chemistry, chloride content, pH and temperature. Outokumpu’s materials-selection guidance similarly asks for the actual environment, concentrations, impurities and temperature, and cautions that laboratory corrosion data may not represent real service conditions.

For abrasive water, provide measured solids information, including concentration and particle size where available. Ask for the permitted conditions for the quoted 4SG configuration rather than applying a limit from another pump family.

If the project requires potable-water approval, identify the required certification and ask for evidence covering the actual supplied model and components. A stainless steel impeller description is not a drinking-water certification.

These checks help decide whether the proposed configuration belongs on the shortlist at all. They should happen before the order is placed, especially where retrieving a pump from the well is costly.

Check The Outlet And Installation Dimensions

The catalogue groups the 4SG outlet information as follows:

FamilyCatalogue Outlet NotationConfirmation Needed
4SG2 and 4SG31.25-inchExact thread and supplied connection
4SG51.5-inchExact thread and supplied connection
4SG8 and 4SG142-inch, with 1.5-inch in parenthesesWhich connection is supplied and what the parenthetical size represents

The last notation should not be interpreted as proof that every pump includes both connections or an adapter. Have the quotation state the supplied outlet size, thread standard and any included transition fitting.

The nominal outlet is also not an automatic instruction to use the same pipe diameter throughout the installation. Check losses and pressure requirements for the complete route using the submersible pump pipe size guide.

For physical fit, compare the smallest clear borehole diameter with the maximum dimension of the complete assembly, including cable protection and connection hardware. The 4-inch category name does not establish installation clearance.

Length also changes between models. The catalogue’s pump-body length column lists 515 mm for 4SG8/12 and 599 mm for 4SG8/15. Those values are labelled pump-body dimensions; do not use them as confirmed overall pump-and-motor lengths.

Request a complete assembly drawing if the well is restricted, deviated or fitted with a liner. Also confirm motor-cooling requirements for the intended installation rather than treating physical fit as the only acceptance test.

Request A 4SG Submersible Pump Quote You Can Compare

A useful enquiry describes the required service and the supply scope. Send Liyuan:

  1. Required flow and total dynamic head, including the expected operating range.
  2. Pumping water level at the stated flow, well yield, well depth and minimum clear casing diameter.
  3. Voltage, frequency, phase and any existing motor, control box or drive details.
  4. Water temperature, water analysis and measured sand or solids information.
  5. Pipe details, required outlet connection and any installation-space restrictions.
  6. Whether you need a pump end, complete pump-and-motor assembly, or an assembly with cable and controls.

If you do not know total dynamic head, send the underlying water-level, pressure, elevation and pipe information instead of guessing a pump model from well depth.

Ask the quotation to identify the exact 4SG model, matched motor, approved performance curve, material schedule, complete dimensions and included accessories. Request price, lead time and commercial terms for that defined package; this page does not assume a standard delivery time or warranty.

When comparing two offers, keep the duty point, frequency, material requirements and supply scope the same. A cheaper pump-end-only offer is not directly comparable with an offer that includes the motor, cable and controls.

To discuss the available Liyuan submersible pump range, send your duty requirements together with any proposed 4SG model. The aim is a documented selection, not simply the highest-head model in the table.

Frequently Asked Questions About 4SG Pumps

Is Every 4SG Pump From Different Suppliers Equivalent?

No. Treat the manufacturer, full model and approved specification as one identity. A shared series label does not verify interchangeability.

Does The 4SG8 Always Deliver 8 m³/h?

No. The tables show several flow points for each configuration. Actual delivery depends on the selected pump curve and system conditions.

Are All Liyuan 4SG Parts AISI 304?

The supplied performance pages identify stainless steel impellers but do not establish an AISI 304 specification for every component. Request a model-specific materials list.

Can I Order A 4SG Submersible Pump From Horsepower Alone?

No. The 4SG8/12 and 4SG8/15 example demonstrates different head values at the same flow despite identical listed motor power. Specify flow, head and operating conditions before choosing the model.

Email:Liyuan@liyuan-pump.com

WhatsApp:+86 181-2828-2767

Phone: USA 86-134 2250 1007

General Questions
Quotes, Please use Sales Quote Form HERE Email: liyuan@liyuan-pump.com
Quick Connect
Scroll to Top

Get a Quote